 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| SIDACtor (R) Protection Thyristors Broadband OptimizedTM Protection MC Series - DO-214 Description MC Series DO-214 are low capacitance SIDACtor(R) devices designed to protect broadband equipment such as VOIP DSL modems and DSLAMs from damaging , overvoltage transients. The series provides a surface mount solution that enables equipment to comply with global regulatory standards while limiting the impact to broadband signals. Features and Benefits Low voltage overshoot Low on-state voltage Agency Approvals Agency Agency File Number E133083 Does not degrade with use Fails short circuit when surged in excess of ratings Applicable Global Standards 40% lower capacitance than our Baseband Protectors, for applications that demand greater signal integrity Pinout Designation NOT APPLICABLE Schematic Symbol TIA-968-A TIA-968-B ITU K.20/21 Enhanced Level* ITU K.20/21 Basic Level* GR 1089 Inter-building* *A-rated parts require series resistance GR 1089 Intra-building* IEC 61000-4-5 YD/T 1082 YD/T 993 YD/T 950 Electrical Characteristics VDRM @lDRM=5A V min P0080SAMCLRP P0220SAMCLRP P0300SAMCLRP P0080SCMCLRP P0220SCMCLRP P0300SCMCLRP P0640SCMCLRP P0720SCMCLRP P0900SCMCLRP P1100SCMCLRP P1300SCMCLRP P1500SCMCLRP P1800SCMCLRP P2100SCMCLRP P2300SCMCLRP P2600SCMCLRP P3100SCMCLRP P3500SCMCLRP P-8AM P02AM P03AM P-8CM P02CM P03CM P06CM P07CM P09CM P11CM P13CM P15CM P18CM P21CM P23CM P26CM P31CM P35CM 6 15 25 6 15 25 58 65 75 90 120 140 170 180 190 220 275 320 VS @100V/s V max 25 32 40 25 32 40 77 88 98 130 160 180 220 240 260 300 350 400 IH mA min 50 50 50 50 50 50 150 150 150 150 150 150 150 150 150 150 150 150 IS mA max 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 IT A max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 VT @IT=2.2 Amps V max 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 Capacitance @1MHz, 2V bias pF min 25 25 15 25 30 25 55 50 45 45 40 35 35 30 30 30 30 25 pF max 55 50 35 75 65 45 85 75 70 70 60 55 50 50 50 45 45 40 Part Number Marking Notes: - Absolute maximum ratings measured at TA= 25C (unless otherwise noted). -(c) 2011 Littelfuse, Inc. Devices are bi-directional (unless otherwise noted). Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 72 Revised: February 22, 2011 SIDACtor (R) Protection Thyristors Broadband OptimizedTM Protection Surge Ratings Series IPP 0.2x310 1 0.5x700 2 A min A C Notes: 1 Current waveform in s 2 Voltage waveform in s 2x10 1 2x10 2 A min 150 500 8x20 1 1.2x50 2 A min 150 400 10x160 1 10x160 2 A min 90 200 10x560 1 10x560 2 A min 50 150 5x320 1 9x720 2 A min 75 200 10x360 1 10x360 2 A min 75 175 10x1000 1 10x1000 2 A min 45 100 5x310 1 10x700 2 A min 75 200 ITSM 50/60 Hz A min 20 30 di/dt A/s max 500 500 20 50 - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP - The device must initially be in thermal equilibrium with -40C < TJ < Thermal Considerations Package DO-214AA Symbol TJ TS R0JA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient 90 Value Unit C C C/W V-I Characteristics tr x td Pulse Waveform +I IPP - Peak Pulse Current - %IPP IT IS IH IDRM -V VT VDRM VS +V 100 Peak Value tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 -I tr td t - Time (s) Normalized VS Change vs. Junction Temperature 14 12 10 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Normalized DC Holding Current vs. Case Temperature 2.0 Percent of VS Change - % IH (TC = 25C) 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 IH 25 C 25C Ratio of Junction Temperature (TJ) - C Case Temperature (TC) - C (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 73 Revised: February 22, 2011 SIDACtor (R) Protection Thyristors Broadband OptimizedTM Protection Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pb-Free assembly (see Fig. 1) Figure 1 TP Ramp-up tP Critical Zone TL to TP Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) 60-180 secs. 3C/sec. Max. 3C/sec. Max. 60-150 secs. Temperature Average ramp up rate (Liquidus Temp (TL) to peak) TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) TL TS(max) Preheat tL Ramp-down TS(min) tS Peak Temp (TP) Time within 5C of actual Peak Temp (tp) Ramp-down Rate Time 25C to Peak Temp (TP) Do not exceed 30 secs. Max. 6C/sec. Max. 8 min. Max. 25 time to peak temperature (t 25C to peak) Time Physical Specifications Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC JEDEC, JESD22-A-101 JEDEC, JESD22-A-101 -65C, 1008 hrs. 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 JEDEC, JESD22-A-102 Temp Cycling UL recognized epoxy meeting flammability classification 94V-0 Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 74 Revised: February 22, 2011 SIDACtor (R) Protection Thyristors Broadband OptimizedTM Protection Dimensions -- DO-214AA Case Temperature Measurement Point CA 0.079 (2.0) Pad Outline 0.079 (2.0) B D Dimensions A Inches Min 0.130 0.201 0.077 0.159 0.030 0.075 0.002 0.077 0.006 Millimeters Min 3.30 5.10 1.95 4.05 0.75 1.90 0.05 1.95 0.15 Max 0.156 0.220 0.087 0.181 0.063 0.096 0.008 0.104 0.016 Max 3.95 5.60 2.20 4.60 1.60 2.45 0.20 2.65 0.41 0.110 (2.8) inch (millimeter) B C D E F G H K H E F K G Part Numbering P xxx 0 S C MC L RP TYPE P = SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE REEL PACK RoHS COMPLIANT Part Marking MC Series IPP RATING Pxxxx xxxxx Part Marking Code (Refer to Electrical Characteristics Table) Date Code Packing Options Package Type S Description DO-214AA Tape & Reel Pack Quantity 2500 Added Suffix N/A Industry Standard EIA-481-D Tape and Reel Specification -- DO-214AA 0.157 (4.0) 0.472 (12.0) 0.36 (9.2) 0.315 (8.0) 12.99 (330.0) 0.059 DIA (1.5) Cover tape 0.512 (13.0) Arbor Hole Dia. Dimensions are in inches (and millimeters). 0.49 (12.4) Direction of Feed (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 75 Revised: February 22, 2011 |
Price & Availability of P0080SAMCLRP
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |